
Stops the Chemical Reaction of PUR Hot Melt Adhesives
A fully functional adhesive application system and melter are of major importance for a smooth and reproducible adhesive application. The cleaning effort varies depending on the application system and unit, and depends largely on the type of adhesive used. If the old and the new hot melt adhesive have different chemical bases, it is necessary to clean the equipment more thoroughly.
Before the cleaning of the application system is started, it must be tested whether the adhesives are compatible with each other as well as with the Good Adhesive flushing agents and cleaners. Especially in closed application systems it should be ensured that the PUR hot melt adhesive and the Good Adhesive flushing agent are melted evenly, to prevent plugged hoses and nozzles due to an unwanted reaction.
If the processed adhesive was a PUR hot melt, it is especially important that the system be cleaned before extended downtimes (e.g. on weekends, holidays, periodic shutdowns, etc.). Good Adhesive supplies a range of flushing agents and cleaners for that purpose.
Modern PUR hot melt adhesives for edgebanding are characterised by a moderate reactivity and thus a relatively slow chemical crosslinking process. In many cases, the PUR hot melt adhesive can therefore remain in the heated tank overnight without the system having to be cleaned. However, this is not a universal characteristic and depends on the individual PUR hot melt product. Please contact a specialist from Good Adhesive to check whether the adhesive used in your application generally also provides this processing advantage.

Melter (Pre-Melter) and Hoses
The primary task of a flushing agent is to physically push out the adhesive from the hoses and the application unit, and therefore to purge product remnants from the system. Due to the general flow behaviour of liquids the flow velocity is significantly lower at the walls compared to the centre of the hose. To ensure that the hoses are cleaned thoroughly, it is thus necessary to use a sufficient amount of flushing agent.
Apart from the flow velocity, viscosity also plays a role in the purging process. If the viscosity of the flushing agent is too low, it will only purge the adhesive in the centre of the hose. Under those circumstances, it will not be possible to remove all the adhesive. To find out the viscosity of the flushing agent and the hot melt adhesive, please refer to the corresponding Technical Data Sheets.
The unit is to be emptied and flushed with the flushing agent until all PUR hot melt adhesive has been extruded from the system. Remnants of flushing agent should remain in all adhesive-carrying machine parts. When the flushing agent cools, it will shrink, thus increasing the cleaning effect.

Melting Tank (Glue Pot)
At processing temperature, drain as much as possible of the PUR hot melt adhesive from the melting tank. Carefully remove as much as possible of the PUR hot melt remnants from the walls.
Fill the suitable flushing agent (depending on the adhesive type) into the melting tank. To increase the cleaning effect, use a wooden/silicon spatula to spread the granulate in the hot tank before melting. Be careful not to damage the coating on the walls. Wait until all the flushing agent has melted.
Allow the flushing agent to soak and circulate between the melting tank and the application roller for at least half an hour at processing temperature of the previously used hot melt adhesive. During this process, the application roller must rotate to prevent the adhesive from flowing into the machine.
After the flushing agent has soaked sufficiently, empty the tank. Alternatively, turn off the adhesive system to prepare for extended downtime. In the latter case, the cold flushing agent remains in the melting tank.
When the unit is started up again, it is recommended to clean the application roller using a soft brass brush and pressurised air (from a hand gun). The mechanical cleaning must be carried out in a way as to ensure that the anti-stick coating on the application roller and on the melting tank will not be damaged. Please also observe all recommendations of the equipment manufacturer.
Flush the tank at processing temperature with a small amount of the adhesive to be used, to purge the bulk of the flushing agent. It is also recommended to use a wooden spatula to spread the adhesive in the reservoir and then drain it. The flushing agent is coloured to facilitate the detection of contaminated hot melt adhesive.
ABOUT US
Zhejiang Good Adhesive Co., Ltd was established in 1996 in China, covers an area of more than 10000 square meters with annual output of 30000tons of environmental friendly hot melt adhesive series products base on EVA, polyolefin, elastomer, polyurethane, PA and animal protein.
Professional team
We have our own lab and R&D team, can provide you technical supports at any time.
Wide application range
The main application industries of hot melt adhesive include book binding, product packaging, filter, furniture, automobile, medical, aerospace, rail transit and other industries.

30000+Tons
Annual output
8
Production Line
100+M
Annual output value
500+
Business partner
1950-01
Material Office of Zhejiang Rezzsearch Institute of Chemcal Industry.

1990-11
Zhejiang Yida Adhesive Co.,Ltd. established.

2009-10
Zhejiang Good Adhesive Co.,Ltd. established.

2020-08
Guangzhou Gute Adhesion Co.,Ltd established.

2021-01
Completion of share reform.
Establish Shanghai Gute New Material Intelligent Manufacturing Research and Development Center.
Complete the renovation of equipment intelligent manufacturing -3.0, with an annual production capacity of 18000 tons.

2022-04
Establishment of Branch Hubei Gute Chemical New Material Co.,Ltd.

2023-02
Establishment of Jiangsu Gute New Material Technology Co., Ltd.

Companies We Have as Clients
We are looking for a cooperative partner to expand our business.














